[olug] dhcpcd problem

David Walker linux_user at grax.com
Thu Apr 25 15:41:32 UTC 2002


A couple of weeks ago we observed DHCP failing to work with 3 laptops using 
built-in Xircom ethernet/modem under Windows 2000.  We gave up and configured 
them with static IPs as it wasn't worth our time to investigate further.

If you have access to a different brand of ethernet card try that and see if 
it makes a difference.

On Thursday 25 April 2002 10:17 am, Tanya Loughead wrote:
> Thanks everyone for trying to help me.  To better describe my problem, AND
> what I have already tried to fix the problem, my UNIX-mentor suggested that
> I describe my problem in a more "exacting"  manner..... So, these are his
> words-- Sorry that it's so long.  I'm so grateful for your time and help. 
> I solemnly hereby swear to always help other struggling Linux users, if I
> ever get to the point of knowing what the heck is going on!
> So, here it is:
> Problem: connecting to the Internet via Cox cable. DHCP is the
> recommended protocol in Windows and Mac documentation provided
> by Cox, yet what appears to be a correct Linux setup for DHCP
> fails to yield proper network assignments of address, gateway
> or DNS servers.
>
> Configuration: recent Dell laptop, PIII 128 with a Xircom 10/100/modem
> combo PCMCIA, running unpatched Redhat 7.2. The kernel recognizes
> the card and I can plumb the interface as eth0 manually with
> ifconfig(8). Network options are set in /etc/sysconfig/network to
> enable the interface at boot, DHCP is enabled, all according to
> Redhat support documents. Normal runlevel is 3; loopback fails
> initialization. Not sure if/what correct rc scripts for DHCP are
> run or linked at all in /etc/rc3.d/. Make/model of cable "modem"
> unknown.  No samba configured.
>
> Checked: Installation was re-done to ensure DHCP was chosen and
> configured to be used. Apparently netcfg is no longer part of redhat?
> The card is recognized by the stock kernel and the PCMCIA HowTo
> bears this out, although some (unknown if relevant) Xircom bugs
> have been fixed in more recent kernels. The link light activates
> on both the card and the modem.  dhcpcd(8) run by hand generates
> traffic for about a minute - debug output shows timeouts and tx/rx
> lights on card do activate during negotiation. The command exits
> with 14.
>
> A crossover cable and straight-through cat-5 have both been tried,
> each time directly to the modem. A Win98 machine, similarly configured,
> successfully initalizes its network using the same physical
> configuration (via the straight ethernet cable) and DHCP. Lastly,
> the "-r" flag was passed to dhcpcd to check for use of obsolete
> DHCP protocol - nothing, but it did exit with 0 and leave a dummy
> DHCP reserved net configured (169...). dhcpcd used without flags
> (or -d) result in an RFC 1917 assignment (192.168.100) to the
> interface, but no gateway is set. The Win98 machine when it initializes
> gets a real net, address and gateway starting with 68.
>
> I'm hoping that I just haven't done the right dance to properly get
> DHCP to work. I don't think I can completely eliminate the card
> based on the above tests, but it would be quite unusual to have it
> work only half-way. Normally I use NAT with a fixed addresses on
> both sides, so I am unfamiliar with what I *had* understood to be
> a pretty straightforward setup with DHCP.
>
> > -----Original Message-----
> > From: Brian Roberson [mailto:roberson at olug.org]
> > Sent: Wednesday, April 24, 2002 11:22 PM
> > To: olug at olug.org
> > Subject: Re: [olug] dhcpcd problem
> >
> >
> > the #1 thing to check is.....
> >
> > is the driver properly loading into the kernel? here are a few
> > key commands:
> >
> > "lsmod "
> > ( list modeules...  look for your net card driver... trivial, but
> > necisary )
> > ifconfig -a
> > ( if you dont know the module name for your NIC, this will tell
> > you that you
> > have SOMETHING loaded... you should see an interface named eth0 )
> >
> > In redhat, there are quite a few gui's to get your nic setup... I
> > will let a
> > redhat user walk you through those, of course once we determine
> > if your nic
> > is setup at the lowest layer or not.....
> >
> >
> >
> > On Wednesday 24 April 2002 09:41 pm, Tanya Loughead wrote:
> > ....
> >
> > -_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_
> >
> > For help contact olug-help at olug.org - run by ezmlm
> > to unsubscribe, send mail to olug-unsubscribe at olug.org
> > or `mail olug-unsubscribe at olug.org < /dev/null`
> > (c)1998-2002 OLUG http://www.olug.org
> >
> > -_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_
>
> -_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_
>
> For help contact olug-help at olug.org - run by ezmlm
> to unsubscribe, send mail to olug-unsubscribe at olug.org
> or `mail olug-unsubscribe at olug.org < /dev/null`
> (c)1998-2002 OLUG http://www.olug.org
>
> -_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_


-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_

For help contact olug-help at olug.org - run by ezmlm
to unsubscribe, send mail to olug-unsubscribe at olug.org
or `mail olug-unsubscribe at olug.org < /dev/null`
(c)1998-2002 OLUG http://www.olug.org

-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_




More information about the OLUG mailing list